Temperature: 360°-370° for
Hotronix®
(other
machines at 375° or higher) Time:3-5 Seconds
Pressure: Med/Firm 6-8
Allow for warm up time.
Preheat
Bottom Pad
Before applying, lock the top platen down for 60 seconds.
This helps the ink to flow properly during the application.
NOTE: These recommended time, temperature and pressure settings are for Stahls' Hotronix® heat seal machines. Settings on other heat presses may vary based on their inconsistencies.
For Application on cotton, polyester or poly/cotton
blends. Downloadable PDF
1. Preproduction
Please check transfers carefully before
applying. We provide an extra transfer for
testing to your quality standards. Cut transfer
into 4 pieces and apply on test material until
desired results are achieved. If you are
unable to get desired results, please call us
before starting job.
3. Press
Place
the transfer face down on the garment.
Close machine and press 3-5 seconds.
2. Preheat Garment
Place
garment on platen and press for 3-5 seconds
or until there is no more steam to remove wrinkles and
moisture. Check to be sure there are no obstructions
such as buttons, pockets or seams. If there are, raise
print area only with Print Perfect pad or mouse pad.
4. Peel
Open
machine, and peel off transfer paper quickly in a smooth,
even motion.
Polytrans
Temperature: 340° for
Hotronix®
(other machines at 350° or
higher) Time:10 Seconds
Pressure: Med/Firm 6-8
Allow for warm up time.
Preheat Bottom
Pad
Before applying, lock the top platen down for 60
seconds. This helps the ink to flow properly during
the application.
NOTE: These recommended time, temperature and pressure settings are for Stahls' Hotronix® heat seal machines. Settings on other heat presses may vary based on their inconsistencies.
For Application on cotton, polyester or poly/cotton blends.Downloadable PDF
1. Preproduction
Please check transfers carefully before
applying. We provide an extra transfer for
testing to your quality standards. Cut transfer
into 4 pieces and apply on test material until
desired results are achieved. If you are
unable to get desired results, please call us
before starting job.
3. Press
Place
the transfer face down on the garment.
Close machine and press 10 seconds.
2. Preheat Garment
Place
garment on platen and press for 3-5 seconds or until
there is no more steam to remove wrinkles and moisture.
Check to be sure there are no obstructions such as buttons,
pockets or seams. If there are, raise print area only
with Print Perfect pad or mouse pad.
4. Peel
Open
machine, wait 3-5 seconds before peeling off transfer
in a smooth, even motion.
Hot Split
Temperature: 360°-370° for
Hotronix®
(other machines at 375° or
higher) Time:8-10 Seconds
Pressure: Med/Firm 6-8
Allow for warm up time..
Preheat Bottom
Pad
Before applying, lock the top platen down for 60
seconds. This helps the ink to flow properly during
the application.
NOTE: These recommended time, temperature and pressure settings are for Stahls' Hotronix® heat seal machines. Settings on other heat presses may vary based on their inconsistencies.
For Application on cotton, polyester or poly/cotton blends.Downloadable PDF
1. Preproduction
Please check transfers carefully before applying. We provide an extra transfer for testing to your quality standards. Cut transfer into 4 pieces and apply on test material until desired results are achieved. If you are unable to get desired results, please call us before starting job.
3. Press
Place
the transfer face down on the garment.
Close machine and press 8-10 seconds.
2. Preheat Garment
Place
garment on platen and press for 3-5 seconds or until
there is no more steam to remove wrinkles and moisture.
Check to be sure there are no obstructions such as
buttons, pockets or seams. If there are, raise print
area only with Print Perfect pad or mouse pad.
4. Peel
Open
machine, and peel off transfer paper quickly in a smooth,
even motion.
Photo Prints
Temperature: 360°-370° for
Hotronix®
(other machines at 375° or
higher) Time:12-15 Seconds
Pressure: Med/Firm 6-8
Allow for warm up time.
Preheat Bottom
Pad
Before applying, lock the top platen
down for 60 seconds. This helps the ink to flow properly
during
the application.
NOTE: These recommended time, temperature and pressure settings are for Stahls' Hotronix® heat seal machines. Settings on other heat presses may vary based on their inconsistencies.
For Application on cotton, polyester or poly/cotton blends.Downloadable PDF
1. Preproduction
Please check transfers carefully before applying. We provide an extra transfer for testing to your quality standards. Cut transfer into 4 pieces and apply on test material until desired results are achieved. If you are unable to get desired results, please call us before starting job. Cut away blank,
unprinted area of the transfer before applying.
3. Press
Place
the transfer face down on the garment.
Close machine and press 12 - 15 seconds.
2. Preheat Garment
Place
garment on platen and press for 3-5
seconds or until there is no more steam to remove wrinkles
and moisture.
Check to be sure there are no obstructions such as
buttons, pockets or seams. If there are, raise print
area only
with Print Perfect pad or mouse pad.
4. Peel
Open
machine.
T-shirts: Immediately peel off transfer in a smooth,
even motion.
Sweatshirts: Wait 5 seconds before peeling off transfer
in a smooth, even motion.
NOTE: Most problems occur when the base pad has not been
properly preheated. This step should be repeated if production
is interrupted.
Reflective
Temperature: 340° for
Hotronix®
(other machines
at 350° or higher) Time:20
Seconds
Pressure: Med/Firm 6-8
Allow for warm up time.
Preheat
Bottom Pad
Before applying, lock the
top platen down for 60 seconds. This helps
the ink to flow properly during the application.
NOTE: These recommended time, temperature and pressure settings are for Stahls' Hotronix® heat seal machines. Settings on other heat presses may vary based on their inconsistencies.
For Application on cotton, polyester or poly/cotton blends.Downloadable PDF
1. Preproduction
Please check transfers carefully before applying. We provide an extra transfer for testing to your quality standards. Cut transfer into 4 pieces and apply on test material until desired results are achieved. If you are unable to get desired results, please call us before starting job.
3. Press
Place
the transfer face down on the garment.
Close machine and press 20 seconds.
2. Preheat Garment
Place
garment on platen and press for 3-5 seconds or
until there is no more steam to remove wrinkles
and moisture. Check to be sure there are no obstructions
such as buttons, pockets or seams. If there are,
raise print area only with Print Perfect pad or
mouse pad.
4. Peel COLD
Open machine, allow print to cool
completely to the touch.
Remove backing carrier in a
smooth, even motion.
Goof Proof®
Please check transfers carefully before
applying. We provide an extra transfer for
testing to your quality standards. Cut transfer
into 4 pieces and apply on test material until
desired results are achieved. If you are
unable to get desired results, please call us
before starting job.
Place
the transfer face down on the garment.
seconds
or until there is no more steam to remove wrinkles and
moisture. Check to be sure there are no obstructions
such as buttons, pockets or seams. If there are, raise
print area only with Print Perfect pad or mouse pad.
Open
machine, and peel off transfer paper quickly in a smooth,
even motion.
Place
the transfer face down on the garment.
